On Preliminary Processing of Substrate to Decrease of Mismatch-Induced Stresses in a Heterostructure
Abstract
In this paper, we introduce an approach to reduce mismatch-induced stress in a heterostructure by using radiation processing of the substrate prior to epitaxial layer growth from the gas phase. Within the framework of the approach, mismatch-induced stresses in the heterostructure can also accelerate recombination and the diffusion of radiation defects from the damaged region during growth from the gas phase at high temperature. We also consider an analytical approach for analyzing mass and heat transfer. The approach allows simultaneous consideration of spatial and temporal variations in the parameters of mass transfer. At the same time, the approach allows for the consideration of the nonlinearity of the processes under consideration.
Keywords:HeterostructureMismatch-induced stressesRadiation processingGrowth from gas phaseRadiation
processing analytical approach for analyzing mass and heat transfer.
1. Introduction
The widespread use of multilayer structures for the manufacturing of solid-state electronic devices necessitates improving the properties of their constituent epitaxial layers. At present, several technological processes are used to grow multilayer structures: molecular beam epitaxy, gas-phase epitaxy, and magnetron sputtering. A large number of works consider the growth and use of heterostructures, given their widespread use [1–10]. It is well known that heterostructures experience strain due to lattice mismatch. In this paper, we consider the possibility of reducing mismatch-induced stress by radiation-processing the substrate before epitaxial layer growth. After that, we consider the heterostructure during its growth in a reactor from the gas phase (see Fig. 1). We also introduce an analytical approach for analyzing mass and heat transport. The approach allows simultaneous consideration of both spatial and temporal changes in mass-transfer parameters. The approach also allows consideration of the nonlinearity of the processes.
2. Method of Solution
To achieve our aim, we calculate the spatio-temporal distributions of radiation defect concentrations by solving the following system of equations [11–14].
with boundary and initial conditions I(r,,z,0)=fI(r,,z), I(0,,z,t), , ,
, V(r,,z,0)=fI(r,,z), V(0,,z,t),
, , I(r,-1,z,t)=I(r,1,z,t)=I(r,-1,z,t)=
=I(r, +1,z,t), V(r,-1,z,t)=V(r,1,z,t)=V(r,-1,z,t)=V(r, +1,z,t).
Here I (r,,z,t) is the spatio-temporal distribution of concentration of radiation interstitials with equilibrium distribution V*; V (r,,z,t) is the spatio-temporal distribution of concentration of radiation vacancies with equilibrium distribution V*; DI(r,,z, T), DV(r,,z, T), DIS(r,,z, T), DVS(r,,z, T) are the coefficients of volumetric and surficial diffusions of interstitials and vacancies, respectively; terms V2(r,,z,t) and I2(r,,z,t) correspond to generation of divacancies and diinterstitials, respectively (see, for example, [14] and appropriate references in this book); kI, V(r,,z, T), kI, I(r,,z, T) and kV, V(r,,z, T) are the parameters of recombination of point radiation defects and generation of their complexes. Spatio-temporal distributions of divacancies V (r, z, t)) and diinterstitials I (r, z, t)) could be determined by solving the following system of equations [13], [14].
with boundary and initial conditions
, , ,
, , ,
V(r,,z,0)=0, V(0,,z,t),I(r,,z,0)=0, I(0,,z,t),
I(r,-1,z,t)=I(r,1,z,t)=I(r,-1,z,t)=I(r, +1,z,t), V(r,-1,z,t)=
=V(r,1,z,t)=V(r,-1,z,t)=V(r, +1,z,t).
Here DI(x,y,z, T), DV(x,y,z, T), DIS (x,y,z, T) and DVS(x,y,z, T) are the coefficients of volumetric and surficial diffusions of complexes of radiation defects; kI(x,y,z, T) and kV(x,y,z, T) are the parameters of decay of complexes of radiation defects.
Chemical potential 1 in Eqs. (1) and (2) can be determined by the following relation [11].
1=E(z)ij [uij(r,,z,t)+uji(r,,z,t)]/2, (5)
where E(z) is the Young modulus, ij is the stress tensor; is the deformation tensor; ui, uj
are the components ur(r,,z,t), u(r,,z,t) and uz(r,,z,t) of the displacement vector ; xi, xj are the
coordinate r,, z. Eq. (5) could be transformed to the following form where is the Poisson coefficient; 0 = (as-aEL)/aEL is the mismatch parameter; as, aEL are lattice distances of the substrate and the epitaxial layer; K is the modulus of uniform compression; is the coefficient of thermal expansion; Tr is the equilibrium temperature, which coincides (for our case) with room temperature. Components of the displacement vector can be obtained by solving the following equations [12].
where
, (z) is the density of materials of heterostructure, ij is the Kronecker
symbol. Taking into account the relation for ij last system of equations could be written as The conditions for the system of the above equations can be written in the form.
; ; ;
; ; .
We determine the spatio-temporal distributions of radiation defect concentrations by solving Eqs. (1) and (2) in the framework of the standard method of averaging of function corrections [15–18]. Previously, we transformed Eqs. (1) and (2) to the following form, taking into account initial distributions of the considered concentrations:
(1.а) (2.а)
Further, we replace the radiation defect concentrations on the right-hand sides of Eqs. (1.a) and (2.a) with their not yet known average values 1. In this situation, we obtain equations for the first-order approximations of the required concentrations in the following form.
(1.b)
, (2.b)
Integration of the left and right sides of Eqs. (1.b) and (2.b) over time gives us the possibility to obtain relations for the above approximation in the final form
(1.b)
(2.b) We determine the average values of the first-order approximations to the concentrations of radiation defects using the following Relation (16) [15–18].
. (7)
Substitution of the Relations (1b) and (2b) into Relation (7) gives us the possibility to obtain the required average values in the following form.
where , where .
We determine approximations of the second and higher orders of the concentrations of radiation defects using the standard iterative procedure of the method of averaging of function corrections [15–18]. In the framework of the procedure to determine approximations of the n-th order of concentrations of radiation defects I (r,,z,t), V (r,, z,t), I (r,,z,t) and V (r,,z,t) we replace the required concentrations in Eqs. (1.b) and (2.b) with the following sum: (n+n-1(r,,z,t). The replacement leads to the following transformation of the appropriate equations
(1.c)
(2.c) Integration of the left- and right-hand sides of Eqs. (1.c) and (2.c) gives us the possibility to obtain relations for the required concentrations in the final form
(1.d) (2.d) Average values of the second-order approximations of the required approximations are obtained using the following standard relation [15–18].
. (8)
Substitution of the Relations (1d) and (2d) into Relation (8) gives us the possibility to obtain relations for the required average values 2
2C=0, 2I =0, 2V =0,
where , Further, we calculate solutions to Eq. (6), i.e., the components of the displacement vector. To calculate the first-order approximations of the considered components in the framework of the method of averaging of function corrections, we replace the required functions in the right-hand sides of the equations by their not yet known average values i. The substitution leads to the following result:
Integration of the left and the right sides of the above relations over time t leads to the following result:
Approximations of the second and higher orders of components of the displacement vector could be determined by using standard replacement of the required components in the following sums i+ui(r,,z,t) [15–18]. The replacement leads to the following result:
Integration of the left and right sides of the above relations over time t leads to the following result:
Now we determine and analyze the spatio-temporal distribution of temperature. To analyze the distribution, we determine the solution of the second Fourier law [19].
Here is the speed of flow of mixture of gases-reagents (we consider gases- reagents as ideal gases); c is the heat capacity; T (r,,z,t) is the spatio-temporal distribution of temperature; p (r,,z,t) is the density of power in the system substrate-keeper of substrate; r, , z and t are the cylindrical coordinates and time; C (r,,z,t) is the spatio-temporal distribution of concentration of mixture of gases-reagents; is the heat conductivity. The following relation can determine the value of heat conductivity: , where is the speed of the gas molecules, is the average free path of gas molecules between collisions, cv is the specific heat at constant volume, and is the density of gas.
To solve Eq. (9), we shall take into account the movement of the mixture of gases and the concentration of the mixture. We determine the fluid velocity and concentration by solving the Navier-Stokes equation and the second Fick's law, respectively. We also assume that the radius of the substrate keeper, R, is essentially larger than the thicknesses of the diffusion and near-boundary layers. We also assume the gas stream is laminar. In this situation, the appropriate equations could be written as
, (10)
, (11)
where D is the diffusion coefficient of the mixture of gases-reagents; P is the pressure; is the density; is the kinematic viscosity. Let us consider the regime of the limiting flow, in which all molecules of the deposit material approaching the disk deposit on the substrate; the flow is homogeneous and one-dimensional. In this case, boundary and initial conditions could be written as
C (r,,-L,t) = C0, C (r,-1,z,t) = C (r,1,z,t) = C (r,-1,z,t) = C (r,+1,z,t), C (r,,z,0) = C0 (z+L), C (0,,z,t) , , T (r,-1,z,t) = T (r,1,z,t) = T
(r,-1,z,t) =
T (r,+1,z,t), , , T
(r,,z,0) =
=Tr, ,
T (0,,z,t) , , , vr (r,-1,z,t) = vr
(r,1,z,t) = vr (r,-1,z,t) = vr (r,+1,z,t), v (r,-1,z,t) = v (r,1,z,t) = v (r,-1,z,t) = v (r,+1,z,t), vz (r,-1,z,t) = vz (r,1,z,t) = vz (r,-1,z,t) = vz (r,+1,z,t), vr (r,,-L,t) = 0, vr(r,,L,t) = 0, vr (0,,z,t) , vz(r,,-L,t) = V0, vz(rd2/2,,z[-d2/2,d2/2],0) = zcos tg (1), v (r,,L,t) = 0, v(0,,z,t) , vz(r,,0,t) = 0, vz(r,,L,t) = V0, vz(r,,L,t) =
vz(0,,z,t) , vr(r,,z,0) = 0, v(r,,z,0) = 0,
where =5,6710-8 Wm-2K-4, Tr is the room temperature, is the frequency of rotation of the substrate. Equations for components of velocity of flow with account cylindrical system of coordinate could be written as (10.a)
(10.b)
(10.c)
We determine the solution of this system of equations using the method of averaging of function corrections [15–18]. Within the framework of the approach, we first determine the first-order approximations of the components of the mixture's flow speed. To determine the first-order approximation, we replace the required functions with their average values vr((1r, v(((1(, vz((1z on the right-hand sides of the equations of system (10). After the replacement and calculation of the required derivatives, we obtain equations for the first-order approximations of the components:
, , .
Integration of the left and the right sides with respect to time of the Relations (12) gives us the possibility to obtain the first-order approximations of the components of speed of flow in the final form.
, , . (13)
The second-order approximations of components of speed of flow could be obtained by replacement of the required functions on the following sums vr2r+v1r, v2+ v2r, vz2z+v2r. The average values 2r, 2, 2z are not yet known. Approximations for the components could be written as
(14.a) (14.b)
(14.c)
Integration of the above equations over time leads to the following result:
(14.d)
(14.e)
(14.f)
Further, we determine average values 2r, 2, 2z. The average values have been calculated by the following relations [15–18].
where is the continuous movement of a mixture of gases through the considered horizontal reactor. Substitution of the first- and the second-order approximations of the required components of speed into the Relations (15) gives us the possibility to obtain a system of equations to determine required average values:
where , ,
, , , The solution of the above system of equations could be determined by standard approaches [20] and could be written as
, , , (17)
where ,
In this section, we obtained components of the velocity of the stream of a gas-phase mixture used for the growth of a heterostructure, and the gas carrier in the second-order approximation framework for averaging-function corrections. Usually, the second-order approximation is sufficient for a qualitative analysis of the solution and for obtaining some quantitative results. Let us rewrite Eqs. (10) and (11) by using a cylindrical coordinate system:
In this section, we calculate the components of the speed of the gas reagents used to grow an epitaxial layer and the gas carrier, using a second-order approximation framework for averaging function corrections. Usually, the second-order approximation is sufficient for qualitative analysis and for obtaining some quantitative results. The results of the analytical calculation have been checked against those of the numerical simulation.
To determine the spatio-temporal distributions of temperature and the gas mixture concentration, we used the method of averaging function corrections. To determine the first- order approximations of the required functions, we replace them with their not-yet-known average values 1T and 1C) on the right sides of the above equations. Further, we used the recently considered algorithm to obtain the first-order approximations of temperature and concentration of gas-reagents:
The standard relations could determine the above not-yet-known average values.
Substitution of the first-order approximations for the temperature and gas concentration in Relation (22) yields the following results [20].
The second-order approximations of temperature and concentration of gases- reagents we determine frame the method of averaging of function corrections [15–18], i.e. by replacement of the required functions in right sides of Equations (18) and (19) on the following sums T2T +T1, C2C +C1. In this case, the second-order approximations of the above required functions could be written as Average values of the second-order approximations of the temperature and concentration of the mixture (2T and 2C) have been calculated using the following standard relations.
Substitution of the first- and the second-order approximations of temperature and concentration of mixture into Relations (24) gives us the possibility to obtain equations to determine required average values In this paper, we calculate the concentration of radiation defects, components of the displacement vector, and the speed of flow of the mixture of gases-reagents, as well as the growth temperature, using the second-order approximation framework and averaging of function corrections. The approximation is usually good enough to support qualitative analysis and to obtain some quantitative results. All obtained results have been checked against numerical simulation results.
3. Discussion
In this section, we analyze the dynamics of mass and heat transfer during the growth of films in reactors for epitaxy from the gas phase to determine conditions that improve the properties of epitaxial layers. The main aim of this paper is to analyze the influence of substrate radiation processing on the mismatch-induced stress in the grown heterostructure. Fig. 2 shows distributions of concentrations in the considered heterostructure (a is the thickness of the epitaxial layer after completion of growth) and dependences of the component of the displacement vector uz on the coordinate z.
This figure is shown in the PDF version of the article.
Analysis of the considered processes shows that preliminary radiation processing of the substrate allows decreasing mismatch-induced stress in the considered heterostructure during growth at high temperature. However, one can find a smoother interface between the layers of the heterostructure.
4. Conclusion
In this paper, we introduce an approach to reduce mismatch-induced stress in a heterostructure by radiation processing of the substrate before the growth of epitaxial layers from the gas phase. In this situation, one can observe a decrease in mismatch-induced stress in the heterostructure. Also, one can observe an acceleration of recombination and the diffusion of radiation defects in the damaged area during growth at high temperature. At the same time, the interface between the layers of the heterostructure became smoother. We also consider an analytical approach for analyzing mass and heat transfer. The approach allows simultaneous consideration of spatial and temporal variations in the parameters of mass transfer. At the same time, the approach allows for the consideration of the nonlinearity of the processes under consideration.
Authors' Contributions
All aspects of the research and manuscript preparation were carried out by the author. The author has read and approved the final version of the manuscript.
Funding
Not applicable.
Data Availability
All data supporting the reported findings in this research paper are provided within the manuscript.
Conflict of Interest
The author declares that they have no conflicts of interest.
Consent for Publication
The author confirms consent for the publication of this work.
Ethics Approval and Consent to Participate
This article does not contain any studies with human participants performed by the author.
References
- [1] Stepanenko, I. P. (1980). Fundamentals of microelectronics. Sovetskoe Radio. (In Russian). https://library.ztu.edu.ua/doccard.php/11691
- [2] Gusev, V. G., & Gusev, Y. M. (1991). Electronics. Vysshaya Shkola. (In Russian). https://library.ztu.edu.ua/doccard.php/13150?
- [3] Lachin, V. I., & Savelov, N. S. (2001). Electronics. Phoenix. (In Russian). https://library.bmstu.ru/Catalog/Details/47903?
- [4] Vorob’ev, A. A., Korablev, V. V, & Karpov, S. Y. (2003). The use of magnesium to dope gallium nitride obtained by molecular-beam epitaxy from activated nitrogen. Semiconductors, 37(7), 838–842. https://doi.org/10.1134/1.1592861
- [5] Sorokin, L. M., Veselov, N. V., Shcheglov, M. P., Kalmykov, A. E. E., Sitnikova, A. A., Feoktistov, N. A., ... & Kukushkin, S. A. E. (2008). Electron-microscopic investigation of a SiC/Si (111) structure obtained by solid phase epitaxy. Technical physics letters, 34(11), 992-994. https://doi.org/10.1134/S1063785008110278
- [6] Lundin, W. V., Sakharov, A. V., Zavarin, E. E., Sinitsyn, M. A., Nikolaev, A. E. E., Mikhailovsky, G. A., ... & Tsatsulnikov, A. F. (2009). Effect of carrier gas and doping profile on the surface morphology of MOVPE grown heavily doped GaN: Mg layers. Semiconductors, 43(7), 963-967. https://doi.org/10.1134/S1063782609070276
- [7] Li, Y., Antonuk, L. E., El-Mohri, Y., Zhao, Q., Du, H., Sawant, A., & Wang, Y. (2006). Effects of x-ray irradiation on polycrystalline silicon, thin-film transistors. Journal of applied physics, 99(6), 064501. https://doi.org/10.1063/1.2179149
- [8] Chakraborty, A., Xing, H., Craven, M. D., Keller, S., Mates, T., Speck, J. S., ... & Mishra, U. K. (2004). Nonpolar a-plane p-type GaN and pn junction diodes. Journal of applied physics, 96(8), 4494-4499. https://doi.org/10.1063/1.1790065
- [9] Mitsuhara, M., Ogasawara, M., & Sugiura, H. (1998). Beryllium doping of InP during metalorganic molecular beam epitaxy using bismethylcyclopentadienyl-beryllium. Journal of crystal growth, 183(1–2), 38–42. https://doi.org/10.1016/S0022-0248(97)00336-9
- [10] Talalaev, R. A., Yakovlev, E. V, Karpov, S. Y., & Makarov, Y. N. (2001). On low temperature kinetic effects in metal-organic vapor phase epitaxy of III-V compounds. Journal of crystal growth, 230(1–2), 232–
- [238] https://doi.org/10.1016/S0022-0248(01)01354-9
- [11] Zhang, Y. W., & Bower, A. F. (1999). Numerical simulations of island formation in a coherent strained epitaxial thin film system. Journal of the mechanics and physics of solids, 47(11), 2273–2297. https://doi.org/10.1016/S0022-5096(99)00026-5
- [12] Pankratov, E. L. (2022). On approach to optimize manufacturing of a four stages distributed amplifier to increase density of their elements under influence of miss-match induced stress and porosity of materials on technological process. https://doi.org/10.21203/rs.3.rs-1197911/v1
- [13] Fahey, P. M. (1985). Point defects and dopant diffusion in silicon. Stanford University. https://ui.adsabs.harvard.edu/abs/1985PhDT.........8F/abstract
- [14] Vinetskiy, V. L., & Kholodar, G. A. (1979). Radiative physics of semiconductors. Naukova Dumka. (In Russian). https://elib.spbstu.ru/dl/1618.pdf/download/1618.pdf
- [15] Pankratov, E. L. (2012). Decreasing of depth of p-n-junction in a semiconductor heterostructure by serial radiation processing and microwave annealing. Journal of computational and theoretical nanoscience, 9(1), 41–
- [49] http://jre.cplire.ru/iso/sep11/11/abstract_e.html
- [16] Pankratov, E. L., & Bulaeva, E. A. (2013). Application of native inhomogeneities to increase compactness of vertical field-effect transistors. Journal of computational and theoretical nanoscience, 10(4), 888–893. https://doi.org/10.1166/JNAN.2012.1084
- [17] Pankratov, E. L., & Bulaeva, E. A. (2012). Decreasing of quantity of radiation defects in an implanted-junction rectifiers by using overlayers. International journal of micro-nano scale transport, 3(3), 119–130. https://scispace.com/pdf/decreasing-of-quantity-of-radiation-defects-in-an-implanted-5aax74xf9j.pdf
- [18] Pankratov, E. L., & Bulaeva, E. A. (2013). Doping of materials during manufacture p-n-junctions and bipolar transistors. Analytical approaches to model technological approaches and ways of optimization of distributions of dopants. Reviews in theoretical science, 1(1), 58–82. https://doi.org/10.1166/RITS.2013.1004
- [19] Carslaw, H. S., & Jaeger, J. C. (1959). Conduction of heat in solids . Oxford: Clarendon Press. https://doi.org/10.1016/0022-5096(59)90029-8
- [20] Korn, G. A., & Korn, T. M. (1968). Mathematical handbook for scientists and engineers: Definitions, theorems, and formulas for reference and review. McGraw-Hill Book Company. https://www.amazon.com/Mathematical-Scientists-Engineers-Definitions-Reference/dp/B0000CO5GE